1Z0-996-21 Online Practice Questions and Answers

Critical validation rules verify the integrity of the initial measurement data (IMD). If an implementation needs to add new critical validations, where would you configure them?

A. as new lifecycle algorithms on the IMD Seeder BO (D1-IMDSeeder)

B. in the pre-processing algorithm of the IMD Seeder BO (Dl-IMDSeeder)

C. as options on the IMD Seeder BO (D1-IMDSeeder)

D. in the schema of the IMD Seeder BO (D1-IMDSeeder)

E. in the validation algorithm on the IMD Seeder BO (D1-IMDSeeder)

What happens when a device's measuring components are reconfigured (a new measuring component will be read) at a service point?

A. A device with a new configuration type is created.

B. The original installation event is updated with the "removal" (expire old device configuration).

C. A device with a new configuration type is created. Moreover, a new installation event is created to `install" (new device configuration).

D. The original installation event is updated with the "removal" (expire old device configuration) and a new installation event is created to "install" (new device configuration).

E. A new installation event is created to "install" (new device configuration).

Using a base-supplied algorithm type, what is payment distribution priority typically determined by?

A. Customer Class and Service Agreement Type

B. Payment Type + Debt Age

C. Debt Age

D. Service Agreement Type's Priority and Debt Age

E. Customer Class and Debt Age

Which statement correctly describes the relation between a device and a measuring component?

A. A device configuration links a device only to interval channels.

B. Two measuring components on the same device should have the same Units of Measure (UOM).

C. A device should have only one measuring component type.

D. A device can have any combination of interval and/or scalar measuring components.

Which three statements are true in relation to Financial Transaction creation algorithms? (Choose three.)

A. They control how the payoff balance is affected.

B. They control when a Financial Transaction is to be swept onto a bill.

C. They control how the General Ledger details are created as these must always exist against a Financial Transaction.

D. They control if and how the General Ledger entries are created.

E. They control how the current balance is affected.

Which two statements about usage subscription types are correct? (Choose two.)

A. Usage subscription types define the main billing contact.

B. Usage subscription types define the time zone.

C. Usage subscription types define the valid service point types.

D. Usage subscription types define the recipient of the usage.

What contains the details of how a bill was calculated and how it will be printed on a bill?

A. Calculation Rules

B. Rate Schedule

C. Service Agreement

D. Bill Segments

E. Bill

Which three statements are true about the different types of measuring components? (Choose three.)

A. Seconds-per-interval (SPI) is one of the attributes of scalar measuring components.

B. Only physical measuring components reference a device configuration.

C. The terms register and channel are synonyms for measuring component.

D. The measuring component types are physical, standalone, scratchpad, and TOU.

E. Scalar measuring components contain a single measurement for an arbitrary period of time.

What can cause multiple bill lines for a rate component to be produced in a bill calculation header?

A. changes in Rate Schedule and Bill Factor

B. changes in Rate Version Calculation Group and Bill Factor

C. change in Bill Factor

D. change in Rate Version Calculation Group

E. change in Rate Schedule

Your client has three requirements:

1.

Apply validations on meter reads coming from the Data Collectors.

2.

If a meter read does not pass the validation, an error will be generated and assigned to a user.

3.

Retry the validation every 30 minutes for the errors in case the issue is related to configuration. Which statement describes the base functions you should use?

A. If a To Do entry is created on the VEE exception, the IMD's Next Retry Date/Time is set to 30 minutes, and then processed by the algorithm D1-COMP-TD (Complete To Do Entries).

B. If a To Do entry is created on the VEE exception, the IMD's Next Retry Date/Time is set to 30 minutes, and then processed by the algorithm D1-IMD-RETRY (Retry Initial Measurement Data Processing)

C. If a To Do entry is created on the VEE exception, the user will need to discard the IMD and a new IMD will be loaded after 30 minutes.

D. If a To Do entry is created on the VEE exception, the IMD's Next Retry Date/Time is set to 30 minutes, and then processed by the algorithm D1-CRE-IMDTD (Create To Do)

E. If a To Do entry is created on the VEE exception, the user will need to discard the IMD and a new IMD will be manually loaded.