3605 Online Practice Questions and Answers

The SNMP counters check for authorization failures and other types error conditions. Which of these SNMP error conditions is displayed in Enterprise Device Manager?

A. PCAP packet capture counters

B. In Bad Community Names counters

C. Fan Failure packet counters

D. Power Supply Failure packet counters

A campus network requirement is to introduce Virtual Routing and Forwarding (VRF) in the existing Ethernet Routing Switch (ERS) 8600-based core. The technician has to configure VRF on the ERS 8600. Which statement represents the order for configuring a new VRF?

A. Creating a new VLAN, add an IP address to the VLAN, create the VRF in the VLAN configuration.

B. Create VRF, change context to the new VRF, add an IP address, create a new VLAN, and move the VLAN to the new VRF.

C. Create a VRF, change context to the new VRF, create a new VLAN, add an IP address to the VLAN.

D. Create a VRF, create a new VLAN, move the VLAN to the new VRF, change context to the new VRF, and add an IP Address.

Which VLAN/VLANs should be included on the Inter Switch Trunks (IST) for a proper functioning split Multi-Link (SMLT) configuration?

A. Only VLAN 101

B. Only VLAN 1 and the IST

C. Only the VLANs that are also included on the SMIT/SLT uplinks3

D. The IST VLAN and all the VLANs that are included on all SMLT/SLT links

When configuring Single Link Trunking (SLT) or Split Multi-Link Trunking (SMLT), what can be done to facilitate easily adding more VLANs to the network without impacting traffic?

A. 802.1Q-tag uplinks.

B. Disable STP on the ports.

C. Index the ports.

D. Use redundant MLTs.

Before enabling IP Source Guard through Device Manager, which two conditions must be met on the system (Choose two)

A. Dynamic Host control Protocol (DHCP) snooping must be enabled globally

B. EAPOL must be enabled.

C. The bsSourceGuardConfigMode MIB object must be removed.

D. The port is an untrusted DHCP snooping and dynamic ARP Inspection port

The goal of the Converged Campus architecture is to provide a highly reliable infrastructure with subscribed failover preventing any interruption of traffic on the network? What are the two primary benefits of this design goal? (Choose two)

A. In the event of a failure, no less of connectivity or application availability will be experienced by the end user.

B. This architecture provides high performance Layer 3 switching, resiliency, security, and services.

C. This design goal provides numerous connectivity options including Asynchronous Transfer Mode (ATM), Packet over SONET (POS), and 10 Gigabit Ethernet.

D. The design goal provides the ability to provide hitless software upgrade for the core of the network.

Consider the following deployment requirements Support 40 100 Mb/s VoIP telephones, each with a power requirement of 6 Watt Support 40 directly connected 1000 Mb/s Ethernet workstations with UTP cable

Support four 1Gb/s Ethernet uplinks to the core switch using multimode fiber.

Which configuration is the minimum hardware required for an Ethernet Routing Switch (ERS) 8306 chassis that will support the above requirements?

A. Two 8348TX-PWROne 8393SF

B. One 8348GTxOne 8348Tx-PWROne 8393SF

C. One 8348GTxOne 8348Tx-PWFOne 8308 XLOne 8393SF

D. Two 8348GTx-PWFOne 8308XXOne 8393SF

One of the switches in the Ethernet Routing Switch (ERS) stacks files and is replaced. The auto unit replacement (AUR) is enabled but the stack is not functioning

properly.

What is the problem?

A. The switches in the stack are not identical

B. the stack power was left on during the switch replacement.

C. The switches in the stack are not running the same release of software

D. The stack has two switches with Force Stack disabled.

In Ethernet Routing Switch (ERS) 5600 switch was added into the existing ERS 5500 stack, but ft did not form a proper stack. Which statement describes the problem?

A. The ERS 5600 was set as the Base Unit.

B. The stack was reset for a change in Base Unit to take effect.

C. The mode parameter on the ERS 5600 switch was set to Mixed Mode.

D. The ERS 5500 was set as the Base Unit.

A technician is preparing to update an Ethernet Routing Switch (ERS) 550D and needs to see the existing configuration. How is the information to be displayed?

A. Use the show running-config command.

B. Use the configuration parameter qualifier.

C. Use the show alt-modules command.

D. Use the verbose qualifier.